As local gate fitters based here in Norbury, we supply and hang side gates, garden gates and made-to-measure pairs across SW16, usually on new posts so they keep opening and locking properly for years. Our nearest documented gate jobs are below.
Most gate problems are post problems. A gate is a heavy lever hanging off one post, so if that post is too thin or not set firmly, the gate drops, catches on the ground and stops latching. When we replaced David's double gates in Earlsfield we took the old posts out and set new 6-inch posts to carry the weight of the new pair.
Gardens in Norbury are mostly clay, which shifts a little between wet winters and dry summers, so we set gate posts deep and firmly rather than reusing a tired post that has already started to move.
We often hang the gate as part of a new fence, as on Barry's job in Croydon, where a new gate with locks that open from both sides went in alongside 13 closeboard panels.
A 400mm dig-out and new block paving driveway with eco drains to a soakaway at the front, and closeboard fencing, a gate, two 7m brick flower beds and a Marshalls block paving patio at the back, in two weeks for £20,000 including VAT.
An old fence replaced with 13 heavy-duty closeboard panels at 2m on concrete posts and concrete gravel boards, plus a new gate with locks on both sides, in two days for £3,150 including VAT.
Every photo here is from David's tongue and groove double gates in Earlsfield SW18, fitted in a single day.
↗New double garden gates with ledged and braced frame between brick pier and new post01↗New tongue and groove double garden gates in Earlsfield SW1802↗Pair of made-to-measure timber gates between a brick pier and new post03↗New double gates fitted on 6-inch posts in an Earlsfield garden04↗Outside face of the new tongue and groove gates05↗Finished double gates beside the brick pier and hedge06
Materials & possibilities
Which gate suits a Norbury side passage?
The width of the opening, how often it is used and whether the bins go through it all shape the right gate.
01
Tongue and groove
Solid and private
Boards fitted tightly edge to edge, ledged and braced so the gate stays square. David's pair in Earlsfield was made to the measured opening.
02
Closeboard to match the fence
A seamless run
Where a new fence goes in, the gate can match it, as on Barry's 2m closeboard fence in Croydon.
03
Double gates
Wide openings
A pair of gates opens up a wide side passage or entrance, with a lock that works from either side.
Hinges, braces and locks
A braced frame on the garden side stops a timber gate dropping at the corner, and strong hinges spread the load into the post. We fit locks that open from both sides where people need to come and go, and check the swing and the gap at the bottom before we leave.
From first ideas to finishing touches
A clear path to your finished garden.
01
Measure
We measure the opening and check the posts on each side.
02
Choose
Agree the style, the hinges and how the gate locks.
03
Fit
Old gate and posts out, new posts set, gate hung.
04
Check
Swing, gaps and latching tested before hand over.
BeforeAfter
Documented project · Earlsfield SW18 · 3.7 miles from Norbury
Made-to-measure double gates in Earlsfield
David's old double gates in Earlsfield had worn out. In one day we removed the gates and their posts, set new 6-inch posts and hung a made-to-measure pair of tongue and groove gates, ledged and braced on the garden side, with new hinges and locks that work from both sides. £2,150 including VAT. Drag the slider to compare.
A made-to-measure pair of tongue and groove gates with new posts in Earlsfield cost £2,150. Gates fitted with new fencing cost more overall: £3,150 for 13 panels and a gate in Croydon, and £4,820 for 12 panels on extended posts with a new gate in Beckenham. The size of the opening and the number of gates make the difference.
Prices as shown on each case study. Every garden is different, so your price is fixed in a written quote after a free survey.
Norbury · SW16
Gate fitters on your doorstep in Norbury
Our base is here in Norbury, so gate jobs in Norbury Park, Pollards Hill, Crown Point and Norwood Grove are close to home. We also fit gates across Streatham, Thornton Heath and Upper Norwood.
For a new gate onto a road or driveway, any planning questions in Norbury go to Croydon Council.
David's made-to-measure pair of gates with new posts in Earlsfield cost £2,150 including VAT. A gate fitted with 13 new closeboard panels in Croydon came to £3,150 in total.
Why does my old gate drop and stick?
Usually the post has moved or rotted, or the gate has no brace to keep it square. New posts and a ledged and braced frame fix both.
Can you make a gate to fit an odd-sized opening?
Yes. David's tongue and groove gates in Earlsfield were made to the measured opening rather than bought off the shelf.
Can I unlock the new gate from the street side too?
Yes. Both David's pair in Earlsfield and Barry's gate in Croydon have locks that open from either side.
How long does it take to fit a new gate?
David's old gates and posts came out and the new pair was hung in a single day.
Should I replace the gate when I replace my fence?
If the gate is tired, doing both together means it matches and shares new posts. Gemma's fencing in Streatham and Barry's in Croydon both had a new gate in the same job.
Which parts of Norbury do you fit gates in?
All of it. Our base is in Norbury SW16, and we cover Norbury Park, Pollards Hill, Crown Point and Norwood Grove as well as Streatham Vale and Thornton Heath.
Let's make a start
Your next chapter starts in the garden.
Tell us about your garden gates project in Norbury. We will get in touch to discuss your ideas and the next step towards a site survey.